Housing, construction; P250

For technicians and partly for sales managers!

 

 

 

Housing

  Hiba! A könyvjelző nem létezik.

Scanner cover

Stack cover Hiba! A könyvjelző nem létezik.

Stack cover mechanics. Hiba! A könyvjelző nem létezik.

Upper cover Hiba! A könyvjelző nem létezik.

Upper cover lock. Hiba! A könyvjelző nem létezik.

Upper cover mounting. Hiba! A könyvjelző nem létezik.

Lower cover mounting. Hiba! A könyvjelző nem létezik.

Remove the housing. Hiba! A könyvjelző nem létezik.

Mount the housing. Hiba! A könyvjelző nem létezik.

Rear cover

 

Construction

 

 

 

The housing of the scanner P250 consists of

·    Base plate (with 6 rubber feet and 4 handles for movements of the scanner).

·    Lower housing with the mountings to the housing truss and the mounting hinge to the upper cover.

·    Lock mechanism and the opening in the lower housing to operate the lock.

·    Upper cover with the mounting hinge to the lower cover; it can not be separated from the lower cover.

·    Stacks’ cover upper part with the mountings to the upper cover; it can not be separated.

·    Lower stack cover; it is mounted to the lower cover and can not be separated.

·    Rear cover with power input, cable entry guide for the camera and other cables and the fan covers.

 

 

Allowed slide dimensions are:

Length:          75.00 to 76.00 mm

Width:            25.00 to 26.00 mm

Thickness:    00.95 to 01.20 mm

 

 

 

 

Since January 2015 a slide’s dimensions check tool is delivered with the scanner.

 

  • If the first character of the serial number is an S the tool is used to check the slide dimensions of the scanners “SCAN, “MIDI” and “DESK””.

 

  • If the first character of the serial number is a P the tool is used to check the slide dimensions of the scanner “P250”.

 

 

·      Please check the slide dimensions before filling the magazine!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

                   Scanner cover

The entire housing of the scanner is divided in functional parts.

While normal scan is in progress, all the covers are closed.

  • Opening of any cover is freely done any time, there are no software controlled lock mechanisms.

 

Stack cover

The stack cover is opened to insert magazines with slides into the input stack for scanning and to remove finished magazines from the output stack.

The stack cover may be opened without stopping the scan process; but the actual slide scan process should be finished.

  • To avoid vibrations, magazine filling actions should be done during slide insert or removal actions or the preview capturing process of a slide.
  • Thanks the stack cover mechanics the stack cover will close itself by gravity; it can not stay open.

 

Upper cover

The upper cover is opened to execute small maintenance or service actions of any kind.

  • The upper cover is opened easily by pushing the upper covers lock button.

 

Lower cover

The lower cover is mounted to the housing truss; it is not designed for easily opening or remove.

 

       Scanner cover mounting

 

 

 

 

 

 

 

 

 

 

                   Scanner cover mounting

 

The entire cover is mounted at 4 positions, two in the front and two positions above the rear wall.

The rear mounting solution consists of a mounting pin on the left and right side respectively; onto these pins the drilling of the cover mounting mechanics is placed. The security bolt fixes the cover mounting.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

In the front of the lower cover there are two mounting clamps, one on the left and one on the right side. These clamps are acting independently if the lower cover is moved frontward (during removal of the cover) or if the cover is moved backward (during mounting the cover).

 

 

 

                  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

               Lower cover mounting

 

The entire cover is mounted at 4 positions, two in the front and two positions above the rear wall.

The rear mounting solution consists of a mounting pin on the left and right side respectively; onto these pins the drilling of the cover mounting mechanics is placed. The security bolt fixes the cover mounting position.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

                   Lower cover

Remove the housing

 

1)     Open the lock of the upper cover by using a 1.5mm hex key wrench or an equivalent tool and open the upper cover until it stops.

2)     Remove the security bolts of the lower cover rear mounting on the left and on the right side respectively.

3)     Remove all the camera cables of the fluorescent scan camera (data, power and trigger).

4)     Pull the rear part of the lower cover mounting on the rear upward about 2 cm, until the fixing bolts release the lower cover mounting.

5)     Move the entire lower cover carefully frontward, until the clamps in the front are disconnected from the base plate mounting.

6)     Pull the lower cover upward on the front side about 5 cm, then move the entire lower cover backward.

7)     Now, the entire cover can be removed upward, nearly in an angle of 30 degrees.

 

 

Mount the housing

 

1)     Make sure, all the cables of the pco edge camera (for fluorescent scan) are disconnected.

2)     Put the cover over the scanner so, that the rear part is higher than the front part (nearly in an angle of 30 degrees) until the rear and the front mounting positions are reached.

3)     Fit the clamps in the front part first.

4)     Fit the pins and holes on the rear part next.

5)     If all four mountings fit correctly, drive in the security bolts.

6)     Connect the power, data and trigger cables to the camera pco edge.

7)     Close all covers.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

                   Upper cover lock

By pushing a 1.5mm hex key wrench or an equivalent tool in thickness into the lock opening of the lower cover the lock operating rod is pushed, via a movement inverter the lock guide is moved backward and the lock guide keeper in the upper cover will be released; the lock is opened.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

                   Upper cover

The upper cover can be opened easily and quickly if any kind of service action has to be done inside the scanner.

To open the upper cover, release the upper cover’s lock by pushing a 1.5mm hex key wrench into the lock opening until the upper cover is released.

 

  • Now, lift up the upper cover and move it upward in direction to the rear of the scanner until it stops; in the end position, the upper cover should stay open.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

               Upper cover mounting

The rear part of the upper cover is mounted to the lower cover by using 2 hinges. Inside the hinges torsion springs are situated.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

               Hinge

As mentioned, the hinge is equipped with a torsion spring. After the fixing pin (1) of the spring mounting is removed, the spring mounting (2) may be rotated by a hex key wrench. With this adjustment the weight of the upper housing can be balanced by the torsion force of the spring. The torsion can be defined in a fourth revolution of the spring mounting.

 

  • The torsion force of the springs in the left and right sided hinge together make the upper cover to stay open.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Movement limiter

The torsion force of these springs, together with the upper cover movement limiter makes the upper cover to stay open in its end position.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

                   Stack cover

The upper stack cover can be opened easily and quickly to insert magazines into the magazine input stack or to remove magazines from the output stack; it can not be separated from the upper cover.

  • Lift up the upper stack cover and move it upward in direction to the rear of the scanner until it stops; in the end position, the stack cover should not stay open.
  • To close the cover, easily release it, the cover closes itself by gravity.
  • This cover stays open only if you are holding it in its end position.

 

 

 

 

 

 

 

 

 

 

 

 

                   Stack cover mechanics

The stack cover mechanics is so constructed, that the cover will close itself by gravity. To reach a smooth and slowly close operation on both cover arms, springs are situated.

The springs create a force against the weight of the stack cover if the stack cover will be closed and, if the stack cover is open, the springs override the dead point by creating a little force to move the stack cover downward until the gravity will acting.

 

  • To fulfill the requirements, the stack cover closing mechanics is adjusted.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

                   Emergency power off switch

The emergency power off switch is situated in the right handed side wall of the scanner and is used to inhibit the power supply; the power distribution is interrupted and all movements are stopped immediately.

 

       Power supply

 

 

  • If the power is supplied again to the scanner, the software must be started again!

 

 

       Task Manager

 

 

 

 

 

 

 

 

 

 

Rear cover

 

 

The rear cover of the housing is divided into three parts, the “Right corner cover”, the ‘Rear wall” and the “Left corner cover”.

 

 

 

 

                   Rear wall

 

Mounting

·       In the positions, where the corner covers are mounted to the rear wall, two supporters are increasing the mechanical stability of the rear wall.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

·       From outside, the rear wall is mounted to the base plate with the bolts 1 and the corner covers are fixed to the rear wall by the bolts 2 and 3 of the corner covers.

 

 

 

 

Power input and mains switch

 

       Power input and main switch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cable entry guide

The cable entry guide covers the cable entry of the cameras and other cables into the scanner.

 

The cables are fixed by rubber inserts.

 

The following cables are guided (full version)

 

·       2x camera link cables of the camera “CIS

·       2x camera link cables of the camera “PCO.edge

·       1x trigger cable of the lumencor SPECTRA

·       1x power cable of the lumencor SPECTRA

·       1x USB cable of the preview camera

 

 

       Cable entry guide  Type: KEL-FG B1; Page 14

 

 

 

 

 

 

 

 

 

 

 

 

 

 Rubber inserts

Because the configuration P250 BF and P250FL is different regarding the amount of cables, different types of rubber inserts in the cable entry guide are used.

 

 

       Cable entry guide  Type: KEL-FG B1; Page 20

 

       Differences between P250BF and P250FL

 

 

 

 

 

 

 

 

Fan covers 1, 2

The fan cover contains the particle and the dust filter.

The particle filter and the dust filter should be cleaned monthly, if the room has an office character (carpeted floor).

If the scanner works in labor surroundings, the cleaning of the filter inserts should be done four times at year.

·       To reach the filter inserts, please pull the fan cover (dust filter cover) easily backward.

 

 

How to cleaning the filters

 

·       If the fan cover is removed, the filters can be separated easily.

·       With canned air, the dust can be blown off from the filters; first blow the air from the scanner side of the filter, the cleaner surface.

·       Fine dust can be removed by using hand warm water mixed with a little bit non-aggressive dishwashing liquid or hand washing lotion; wash the filter inserts, then rinse these.

·       The filters can be blown dry by the use of any (heated) air blower (e.g. hairdryer or fan).

·       Return the filter inserts into the fan cover and mount it.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

                   Left and right corner cover

 

Mounting

The right corner cover is mounted to the base plate with the bolts 4 and 5 and is fixed to the housing truss with the bolt 1; the bolts 2 and 3 are fixing it to the rear wall.

 

The left corner cover is mounted to the base plate with the bolts 4 and 5 and is fixed to the housing truss with the bolt 1; the bolts 2 and 3 are fixing it to the rear wall.

 

  • By removing the bolts 1, 2 and 3 and loosening the bolts 4 and 5 the appropriate corner cover can be removed upward.

 

 

 

Power supply fan cover

 

If the 4 mounting bolts are removed, the dust filter can be reached easily.

·       To clean the filter insert, please see above “Fan covers 1, 2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Construction; P250

 

 

 

The scanner Pannoramic 250 consists if the following main components

1.      Cover mounting on the rear

2.      USB electronics

3.      Pulsed xenon flash light source for brightfield scan mode

4.      Neutral density (ND) filter unit with collimator lens holder

5.      Emergency power off switch

6.      X-Y-Z-ND-motor and flash controller electronics

7.      Brightfield preview illumination

8.      Darkfield preview illumination

9.      Barcode illumination

10. Specimen holder

11. Focus unit

12. Objective changer unit

13. Turret unit

14. Camera changer unit

15. CIS camera for brightfield scan mode

16. PCO edge camera; used if fluorescent scan mode is selected.

17. Power supply and distribution electronics housing

18. Magazine unit (not shown here)

 

 

·       For safety regulations regarding human health and scanner functionality please refer to:         Precautions

 

 

 

 

 

               Base plate and housing truss

The base plate and housing truss consists of the following main components:

·       Base plate with rubber feet and handles; mounted from beneath.

·       Long holes to mount and positioning the scanner truss.

·       Power box, containing the power unit (power supply, distribution and switch board and the power amplifier).

·       USB controller box

 

       Adjust the truss position”; “Mounting of the current amplifier”; “Mounting of the power unit”; “USB controller

 

 

Remove the power box cover

·       Loosen the upper and lower power box cover mounting bolts and remove the mounting bolt in the middle.

·       Pull the power box cover upward

 

 

 

 

 

 

 

 

 

 

 

Transport handles

To move the P250, 4 handles are mounted near the corners of the base plate from beneath.

Pull the handles to the left (on the left side) and to the right (on the right side) and rotate them upward. By using the handles, the scanner can be moved safely by two persons.

 

1.      Pull the handle to the left or to the right respectively until it stops, then

2.      Rotate the handle upward.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 Hide handles

 

After the destination is reached, the handles can be hided again.

1.      Rotate the handle to the rear of the scanner as shown, then

2.      Push the handle in direction to the center until it stops.

 

 

·       In the hidden position, the handle will be fixed against rotating downward from itself.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Construction of the handles

The handles are used to move the P250.

Each handle has two defined positions, the hidden position and the position "in use" (as shown); in both positions a fixing is realized.

 

The fixing, shown as shapes 2a and 2b are used during moving the scan, so the handle will not rotate, it stays always upward.

 

If the handle is pushed into its hidden position, the shapes 1a and 1b fitting each other and the handle can not rotate downward by gravity.

 

  • Before rotating the handle sideward during hiding the handle, push the handle a bit to release the fixing (2).
  • If the hidden position is reached, the fitting of the shapes (1) can be reached by pushing and jarring the handle grip a bit upward and downward.

 

 

 

Rubber feet

The P250 is placed on the table by the use of 6 rubber feet; their positions on the base plate are shown on the right.

The number of the rubber feet and their arrangement reduce vibration and resonance.

·       Drive in the rubber foot in the threaded drilling at the specified position until it stops.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Mounting of the power unit (power supply)

 

The entire power unit (power supply, power distribution and switch board and the power amplifier of the lumencor SPECTRA) is mounted onto the power supply “TDK-Lambda”.

On the lower edge of the power supply mounting discs are situated from beneath, so the power supply can be shifted in the mounting rail, situated on the bottom of the power box.

 

 

Important

Please shift the entire power unit only frontward or backward.

·       If the power unit will be inclined sideward or upward during the removal or insert procedure, the mounting discs will be destroyed!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Remove the Power supply

 

  • Disconnect the power cable or switch off the scanner on the main switch.
  • Remove the power box cover.
  • Remove the rubber inserts.
  • Pull the entire power unit straightly frontward as desired; see also “Important” above.
  • May be the power box cover bolt in the middle must be removed.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Mounting of the current amplifier

 

The relay, to switch the power for the lumencor SPECTRA light engine is situated near to the power output of the power supply “TDK-Lambda”.

 

 

       Current amplifier” and “Lumencor SPECTRA light engine

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

                   Truss

Main components of the truss are

 

·       Scanner unit mounting

·       Turret unit mounting

·       Magazine unit mounting and position adjustment

·       Truss mounting

 

The truss holds the entire scanner mechanics; the microscope part and the scanner part as well, because the distance of the units to each other is very important.

The positioning surfaces of the truss, together with the locating surfaces of the scanner plate and the locating surface of the turret plate define the distance of the units to each other and guarantee the straightness of the optical axis also.

The magazine unit mounting defines the position of the magazine unit in relation to the X-X-stage unit and scanner plate.

The long holes in the truss base plate are used to positioning the truss in relation to the housing.

 

 

 

Truss mounting

Each mounting of the truss consists of a bolt with washer and a bolt nut with washer. The plastic spacer is situated between the base plate and the truss.  

By loosening the mounting nuts, the long holes in the base plate allowing the position adjustment of the entire truss in the mathematical X-direction (left / right).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Truss mounting 2

The truss is mounted to the bolts by using a washer and a bolt nut. With a long hole solution in the truss mounting plate, the position of the truss (the entire scanner) can be adjusted in relation to the housing; no parts of the scanner must touching the housing if all covers are mounted.

By loosening the mounting nuts of the truss with a 10th wrench, the long holes in the truss allow the position adjustment of the entire scanner in the mathematical Y-direction (frontward / backward).

 

       Adjust the truss position”.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The long holes in the truss allow the positioning of the truss in the direction frontward and rearward (the mathematical Y-direction)

 

 

 

 

 

 

 

 

 

 

 

 

 

The long holes in the base plate allow the positioning of the truss in the direction left and right (the mathematical X-direction).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Adjust the truss position

To ensure, that the entire scanner does not touch the housing, and to positioning the stack cover, the position of the scanner truss should be adjusted.

The spacers are mounted from beneath with 6mm hex key bolts and the truss is mounted to the bolts by using a washer and a bolt nut; see also above “Truss mounting””.

 

·    Adjust the position of the truss so, that no internal part touches the housing and the input and output stacks are working correctly.

 

 

Adjust the truss position in the direction frontward / backward (the mathematical Y-direction)

  • Loosen the truss mounting nuts with a 10th key wrench and pull the entire truss frontward until the magazine channel side wall (the input and output stacks) are not covered by the upper cover of the housing.
  • The size of the horizontal gap is not important; it can be about 1 or 2mm; see also the gaps in the upper part of the figure on the right.
  • There should be also a gap between stack rail spacer and the lower stack cover; see the lower part of the figure on the right.
  • Tighten the truss mounting nuts.

 

 

 

 

 

 

 

 

 

 

 

 

 

Adjust the position of the truss in the direction left and right (the mathematical X-direction).

Insert 5 magazines into the input stack and insert the other 5 magazines into the output stack.

If the stack cover will be closed, the stack cover arms should not hit the magazine side wall; there should be a gap to the magazine side wall on the input stack side and on the output stack side as well.

Move the truss to the left or to the right respectively, until the requirements are fulfilled; the size of the gaps should be nearly equal on both sides, this has only an esthetic aspect.

 

  • Loosen the truss mounting bolts on the base plate side from beneath.
  • Define the position of the truss left and right, until the requirements are fulfilled.
  • Tighten the mounting bolts.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Scanner unit

 

The scanner unit consists of:

Scanner plate with the mounting to the truss

Focus unit with objective changer

X-Y-stage unit

Preview unit

 Preview illumination unit

Brightfield scan illumination (ND-filter unit with xenon flash light source)

Mounting standoffs for the X, Y, Z, ND controller

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

                   Scanner plate

The scanner plate consists of

·       Locating surfaces

·       Focus unit’s dovetail mounting

·       Focus unit’s dovetail fixing (1)  

·       X-Y-stage unit’s dovetail mounting

·       X-Y-stage unit’s dovetail fixing (2)

·       Preview unit’s horseshoe mounting (4)

·       Preview illumination unit’s mounting (5)

·       Brightfield scan illumination mounting (ND-filter unit)

·       X-Y-stage unit bumper with mounting (3)

·       Mountings for the X-Y-Z-ND control

 

Locating surfaces

 

To define the distance of the scanner unit in relation to the turret unit and to ensure the straightness of the optical axis, locating surfaces are used.

       Turret and scanner unit mounting” and “Tightening sequence

 

 

Focus and X-Y-stage unit’s dovetail mounting

The dovetail mounting ensures the proper position of the X-Y-stage unit and the focus unit in relation to each other.

·       Insert the unit always until it stops.

 

 

 

 

 

Focus and X-Y-stage unit’s dovetail fixing

 

The mounting of the focus unit with objective changer and the mounting of the X-Y-stage unit are realized with dovetails; these are hold by dovetail fixing clamps.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Preview unit’s horseshoe mounting

 

The horseshoe mounting contains two fixing pins to define the position and a threaded hole for the mounting bolt.

 

       Preview unit mounting

 

 

 

 

 

 

 

                   Horseshoe

The horseshoe is the mounting part of the preview unit, and contains the mountings of following components:

 

 

Horseshoe mounting

 

The entire preview unit is situated on the edge of the scanner plate, parallel to the magazine unit.

The position is fixed with two fixing pins and hold by the mounting bolt.

 

       Scanner unit

 

 

Remove the preview unit

·       Remove the mounting bolt and then the entire preview unit can be removed frontward.

 

Mount the preview unit

·       Fit the fixing pins of the scanner unit into the position fixing holes of the horseshoe and push the entire preview unit onto the edge of the scanner unit.

·       Drive in the mounting bolt.

 

 

 

 

 

 

 

 

 

 

 

 

 

Preview objective and camera holder

The preview objective and camera holder allows the adjustment of the preview camera rotation angle in a limited range.

 

To adjust the camera rotation angle:

  • Hold the camera from beneath (the rear of the camera) and loosen the position fixing bolt a little bit until the camera becomes barely rotate-able.
  • By loosening one of the “Rotation angle” bolts and tightening the opposite bolt, the rotation angle will be modified.
  • If the correct camera rotation angle is found, tighten the “Position fixing” bolt; further information can be found in the chapter “Adjust the preview camera rotation angle”.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Preview illumination unit’s mounting

The preview illumination unit consists of a brightfield unit and a darkfield unit.

The entire unit is mounted with 2 bolts onto the edge of the scanner plate, beside the horseshoe.

 

       The preview illumination unit

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Brightfield scan illumination mounting (ND-filter unit)

The flange of the ND-filter unit is mounted with 4 bolts to the scanner plate.

 

       Neutral density (ND) filter unit

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X-Y-stage unit mounting with bumper

 

The distance of the X-Y-stage unit in relation to the magazine unit is defined by the size of the X-Y-stage unit bumper.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

                   Turret plate

The turret plate is used if the P250 is delivered in the version BF only and contains the mounting for:

 

Camera changer unit

In the drillings of the camera changer the clamp will hold the camera changer mounting.

 

       Camera changer mounting

 

 

 

Supporter position

In this position the supporter bolt with supporter tube is mounted.

 

       Supporter tube

 

 

 

 

 

 

Stiffener (P250 and SCAN)

Because the turret plate is in vertical position in the P250 (and in the SCAN also) a stiffener increases the mechanical stability.

 

 

       “Differences between P250BF and P250FL”; “Turret plate

 

 

 

 

 

 

 

 

 

 

 

 

Attention

The camera changer mounting of the P250 differs in length from the camera tube mounting in the SCAN 150 and the MIDI!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Turret and scanner unit mounting

Because the distance between turret unit and scanner unit is important, the mounting is realized by using a locating surface on the unit and so, the unit is fixed to the truss by using clamps.

 

·       The construction of the clamps for the turret unit and for the scanner unit is identical.

·       The correct mounting of the scanner unit and the turret unit is important for the straightness of the optical axis.

 

 

Only by tightening the clamp bolts in the right sequence, the locating surface fits correctly.

The scanner plate is tightened logically in the same sequence.

 

 

 

 

 

 Tightening sequence

 

1                   Lower rear bolt

2                   Top bolt frontward

3                   Upper rear bolt

4                   Top rear bolt

 

During tightening the clamp bolt (1) move the turret unit (turret plate) or the scanner plate on its upper part carefully sideward (toward and away from the scanner unit or the turret unit respectively) until no movements can be expired or the bolt is tightened. Then tighten the clamp bolt (2). Only this way, the locating surface will fit correctly. The sequence of the bolts (3) and (4) is less important because these bolts are near to each other.

To remove the turret plate or scanner plate, loosen the bolts 1 and 3 and remove the clamp, fixed with the bolts 2 and 4; then the plate can be pulled upward and frontward in an angle of 30 degrees.

 

  Remove or mount the FL reflector turret unit

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

           Magazine unit position

 On the right side of the magazine unit mounting, the magazine unit position adjustment and fixing is realized.

With this solution, many adjustments may be left out, if the magazine unit was removed and mounted again.

 

 

 

 

Adjust magazine unit position

 

The goal of the adjustment is the fitting of the slide loader position in relation to the specimen holder position; so a smooth slide insert and slide removal action can be reached.

 

  • To adjust the magazine unit position, loosen the magazine unit mounting bolts first.

 

By loosening the fixing bolt and driving the adjustment bolt inward or

by driving the adjustment bolt outward and tightening the position fixing bolt, the position of the entire magazine unit can be shifted on the mathematical X-direction (left/right).

 

  • If the desired position is reached, tighten the magazine unit mounting

 

       Adjust the magazine unit position