Setup the driver for the preview camera DFK 21F04

 

·      This procedure is true until the software version 1.14; based on the operating system Windows XP® x32bit

 

·   Driver name:   ”drvInstaller.exe”

The driver is found on the install CD: <CD ROM> \Drivers\Preview camera for current Pannoramic DESK, MIDI and SCAN\.

 

·    Alternatively you can setup the driver for the preview camera via the device manager and the “Hardware wizard”.

 

 

 

Requirements

·       Installed operating system Windows® XP x 32bit

·       The install CD or DVD of the software version to be installed

 

See also:       Preview camera “DFK21F04”

 

·       The installation should be done from a HDD, DVD or a pen drive.

 

 

 

 

 

 

 

 

 

 

1.   Run the file „drvInstaller.exe” from the install folder.

 

·    The setup application will alert you to connect the device. Connect the FireWire cable header into the rear of the Pannoramic scanner. By doing this the application recognizes the preview camera and enables the „Next” button to continue the installation.

 

Press the „Next” button.

 

 

If the camera will not be recognized:

·       Check the correct connection of the external and internal FireWire cable.

·       Try with another external FireWire cable.

·       Try with another FireWire port or controller.

 

Check the camera as described in:        

            How to check the preview camera

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press the „Continue Anyway” button to install the driver.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If setup finished installing the new hardware, a dialog appears to inform, that „The installation has been completed!”. Press „Finish” to finishing installation.

The driver had been successfully installed and the camera is ready for use Mirax Scan.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2.       Install the driver for the preview camera DFK 21F04 via the device manager.

 

 

1.      Click on “Start”, select “Control panel”, “System”, and “Hardware”.

 

 

2.      Select “Device Manager”.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.      If the camera is connected, the item “Imaging Devices” can be found and all connected cameras of this controller are listed. To avoid wrong driver installing, disconnect all other cameras for this install procedure and reconnect them if the installation is finished.

 

If the item “Imaging Devices” can not be found, the camera is not connected, defect or any FireWire cable for the DFK 21F04 has no contact.

 

 

 

 

If the camera will not be recognized

·       Check the correct connection of the external and internal FireWire cable.

·       Try with another external FireWire cable.

·       Try with another FireWire port or controller.

 

Check the camera as described in:        

            How to check the preview camera

 

 

4.      Double click on the item “Generic1394 Desktop camera # ...”.

 

 

 

 

 

 

 

 

 

 

5.      Select “Drivers” and “Update Driver...”.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6.      Select “No, not this time” and click on next.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7.      Select “Install from list ...” and click on next.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8.      Select “Don’t search ...” and click on next.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9.      If the driver for the DFK21F04 was previously already installed, the installed driver can be found here in the list.

 

Select “The Imaging Source Europe GmbH DFK 21F04”

 

10.  Click on “Have Disk ....”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11.  Click on “Browse ....“

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12.  Locate the file and click on “Open”

 

The path is:

... Drivers\Preview camera for current Pannoramic DESK, MIDI and SCAN\data\drivers.

 

 

13.  If the driver was already installed previously, this folder will be offered automatically.

 

14.  Select the file “TISDCam.inf” and click on “Open”.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11. Click on “OK”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12. Click on “Next“

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

16. Click on “Continue anyway“.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

17. Click on “Finish“.

 

After a few seconds the hardware will be recognized by the operating system and then the preview camera is ready for work with the service program or the Program “SlideScanner.exe”.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

End