Install the �VRMagic� preview camera driver

 

 

These instructions describe the procedures to install the driver for the preview camera �VRMagic� onto a computer with the operating system Windows� 7 x 64bit; used with the P250, SCAN, MIDI or DESK!

The shown procedure is based on the install DVD of the software version 1.16; and may be used to install the driver for:

      Brightfield preview creation,

      Darkfield preview creation and

      Barcode capturing.

 

 

 

Contents

 

 

Repair�������� the installed version

 

Remove ����� the installed version

 

Install �������� VRmUsbCam DevKit for Windows X86 3.15b

 

 

 

 

 

 

 

 

 

 

Requirements

      Installed operating system Windows� 7 x 64bit

      The install CD or DVD of the software version to be installed

 

See also:����� Software and driver installation

 

      The installation should be done from a HDD, DVD or a pen drive.

 

 

 

 

 

 

 

 

 

 

 

 

Start the file

<Drive>:\Drivers\Preview camera for Pannoramic 250 FLASH (VRM)\setup.exe

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Select the option to be done

 

      Repair ��� the installed version

Upgrades the installed version of �VRmUsbCam DevKit for Windows X86� to the version X86 3.15b and finishes automatically.

 

 

 

      Remove the installed version

Removes the actual installed version of �VRmUsbCam DevKit for Windows X86�

 

Press �Finish�

 

 

 

 

 

 

 

 

 

 

 

 

Install the VRmUsbCam DevKit for Windows X86 3.15b

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press �Next�

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

      Read the License Agreement

 

 

 

 

 

 

      Check �I Agree�

 

 

Press �Next�

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

      Check �Everyone�

 

 

 

 

 

 

Press �Next�

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press �Next�

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

      Installation in progress

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

      Check �Always ��

 

 

Press �Install�

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press �Next�

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press �Close�

 

      Connect the camera to an USB2.0 port!

      The camera uses an USB 2.0 port, otherwise, if the transfer rate of 480Mb/s can not be reached (USB1.1 or lower), the camera window will disappear automatically after some seconds, without any notice!!

 

 

 

 

 

End