Install the driver for the camera “AxioCam MRm REV.3

 

 

·     This description is true until the software version 1.14; based on the operating system Windows® XP x 32bit

 

 

 

 

 

 

·    The driver is found on the install CD: <CD ROM>\Drivers\Scan Camera - AxioCam MRm Rev.3\Cameras\AxioCam\.

 

·    The camera is installed via the device manager and the “Found New Hardware Wizard”

 

 

 

 

 

 

 

 

 

 

 

Drivers remove procedure

 

1.     Click on “Start”, select “Control panel”, “System”, and “Hardware”.

2.     Select “Device Manager”.

 

 

 

The driver is shown in the device list only, if the camera is connected!

 

 

3.     Right-click on the item “AxioCam” for approx. 1-2 seconds and release it.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4.     In the pull down menu select “uninstall”.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5.     Confirm with “OK”.

 

The camera will disappear from the device list.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Install the device driver for the camera

 

1.     Disconnect the camera for 3-5 seconds; then connect it again.

 

The camera occurs in the device list “Imaging devices”.

 

If the camera is connected, the item “Imaging Devices” can be found and all connected cameras of this controller are listed. To avoid wrong driver installing, disconnect all other cameras (DFK 21F04) for this install procedure and reconnect them after the installation is finished.

 

If the item “Imaging Devices” can not be found, the camera is not connected, defect or the FireWire cable for the AxioCam MRm has no contact.

 

2.     The “Hardware update Wizard” will appear automatically or double click on the item “Carl Zeiss AxioCam MRm”.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.     Select “No, not this time” and click on “Next”.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4.     Select “Install from list ...” and click on “Next”.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5.     Select “Don’t search ...” and click on “Next”.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6.     If the driver for the AxioCam MRm was previously already installed, the driver can be found here in the list.

 

 

7.     Click on “Have Disk ....”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8.     Click on “Browse ....“

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9.     Locate the file.

 

The path is:

<CD ROM>\Drivers\Scan Camera - AxioCam MRm Rev.3\Cameras\AxioCam\.

 

 

If the driver was already installed previously, the folder will be offered automatically.

 

 

 

10.  Select the file “AxioCam.inf” and click on “Open”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11.  Click on “OK”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12.  Select the driver Carl Zeiss AxioCam MR R3 and press the “Next” button

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

13.  Click on “Continue anyway“.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

14.  Click on “Finish“.

Reconnect the preview camera DFK 21F04.

 

After a few seconds the hardware will be recognized by the operating system and then the camera AxioCam MRm is ready for work with the service program or the scan software program.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The driver is shown in the device list

 

 

Close all windows with OK.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

End